Peep sight compound bow11/28/2023 ![]() Can You Shoot A Compound Bow Without A Peep Sight? If you’re looking to narrow down your view, a peep sight is a great attachment to have. You’ll also find that they come in many different sizes that are meant to adapt to a wide range of bow sights. Peep sights come in many different designs, but they all provide a similar outcome. It’s a relatively simple attachment, but it serves a vital purpose.Īlthough it isn’t entirely required, you’ll find it’s widely suggested by many archery enthusiasts. Some of these attachments are geared towards personal preference, while others are almost a requirement for the sake of accuracy, consistency, and more.Ĭrafted to be installed on the string of a bow, peep sights are a small hollowed-out circle that works together with your bow sights. With the many accessories and attachments available for compound bows, some offer more significant benefits than others. The attachment is meant to line up with your bow sights, and this allows you to narrow your field of view for an overall better aim. ![]() Should I Use A Peep Sight On A Compound Bow?.Can You Shoot A Compound Bow Without A Peep Sight?.If you’re looking into getting a peep sight for yourself, this article will have all of the insight you need to decide if they’re a good fit for you. You may not see them on every bow, but a decent peep sight can make a world of difference for your compound bow. If you’re looking to enhance your archery experience, a peep sight is an accessory that can take your skill to the next level. Aside from this, a majority of archery professionals highly suggest investing in a peep sight for compound bows. So, do you need a peep sight on a compound bow? A peep sight isn’t a requirement on every bow, but it’s undeniable that it can help improve a few different factors with your bow’s performance. Are they essential? Could you theoretically go without one? And why would you even want one in the first place? Well, here is all you are going to want to consider. If you’ve recently purchased a compound bow, then you may be wondering about what other attachments and accessories you may need. If you make a purchase through a link, we could earn a commission - at no additional cost to you. Step 6: Mount your bow sight.This post may contain affiliate links. You will be serving the peep in eventually, but not yet. Then release the pressure on the limbs, and the string will grab the peep and suck it down into the string. Once you’ve pressed the bow and separated the strings strands half-and-half, insert the peep. It’s pretty easy to tell if you have more strands on one side of the peep than the other. If you bought a used bow and no peep is inserted, or you removed your peep for some reason and have no idea where half-and-half would be, press the bow, guesstimate, insert the peep and look. This string separates the strands in half, so half of the string sits on one side of the peep notch and the other on the other half. You may find your ideal height is more or less, but this range is a good starting point. If your bowstring is brand new, the string manufacturer will place a piece of serving string through the middle of the bowstring, and it’s there for a reason. Typical peep sight height is usually between 5-1/2- and 7 inches above the center of the D-loop. ![]() Now it’s time to install your peep sight. Once your peep sight is installed, draw your bow outside and make sure the peep is perfectly aligned with the sight housing. Some rests, like those from QAD, have timing marks to help guide you in this case you need a friend to watch the timing marks as you draw. As you draw, the rest’s arm should reach its vertical position about the same time your bow’s cams roll over to let off. You can use a draw board if you have one, or you can simply draw the bow with a release set not to fire and watch as the rest’s arms come up. Timing a rest is not difficult, but it’s a key step in how to set up a compound bow. ![]() If you are using a drop-away rest, you now need to attach the rest’s cable to one of the bow’s limbs or to the down cable, depending on the model of rest you use. The author pulls the cord of a drop-away rest through a bow’s down cable. Just level your bow in a bow vise, follow the rest manufacturer’s instructions to install it to the riser, and eyeball it level. The good news is that all of them are very simple to attach. Many models still connect to the riser via the bow’s Berger hole(s), but some models, like many from QAD and others that have adapted QAD’s Integrate Mounting System, mount to a pair of dovetail slits recessed into the back face of the bow’s riser. The first step for how to set up a compound bow, arrow-rest mounting has changed significantly over the last three years. This QAD arrow rest is attached to the Berger hole, but other models can be installed via a dovetail mount. How to Set Up a Compound Bow, Step-By-Step Step 1: Attached the arrow rest. ![]()
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |